____________________   >   Abingdon   >   System components   >   New Style   >   Hyd-mech band saw m-16A hydmech automatic bandsaw amada

Hyd-mech band saw m-16A hydmech automatic bandsaw amada


Hyd-Mech M-16A Automatic Band Saw 480V 3PH with equipment as described below................$ 46,985.00
In Stock Machine Sale Price $ 42,990.00*
*Offer good for in stock machine only, subject to prior sale.
Delivery: (After receipt of written PO): (1) UNIT IN STOCK AT F.E.C. SUBJECT TO SALE.
Please contact Brian Conn at Fabricating Equipment Company for any additional information.
(***) 648-6370
Hyd-Mech M16A TECHNICAL SPECIFICATIONS
Mitering Capability: 90 to 30 Degrees
Blade Wheel Diameter: 19 Inches
Hydraulic Tank Capacity: 11 US GAL.
Coolant Tank Capacity: 9 US GAL.
Shuttle Stroke: 0 -33 multi-indexing standard
Dimensions (w x l x h): 132 x 90 x 66
MACHINE CONSTRUCTION & FEATURES
Machine Base - The machine base is designed and produced with electro-welded steel components for maximum rigidity and support. A chip removal auger and removable 9-gallon coolant tank are built into the base. Leveling bolts are located at corners of the machine.
7.5 HP Motor - Heavy-duty gearbox and 7.5 HP motor, which is controlled by an AC inverter drive. Blade speed is easily adjusted from the control console and the wide range of available band speeds allows for efficient cutting of many types of material.
Blade Wheels - 19 high quality cast iron wheels with heavy-duty wheel & gearbox shaft bearings.
Powered Blade Brush - driven off the blade drive wheel keeps the blade gullets clean, helping to maximize blade performance and life.
Blade Tensioning - hydraulic blade tensioning provides consistent automatic blade tension while allowing quick and easy un-tensioning for blade changing.
Hydraulic System - a 3HP driven hydraulic pump supplies system pressure. The system pressure through 3-position directional valves controls all vising, head up/down, head swing, shuttle movement, and blade tension functions The pump and motor assembly and hydraulic manifold complete with all function directional valves all swing out with the hydraulic compartment door for easy service access, and minimal downtime.
Electrical System - the electrical control components are housed in a console in the front of the machine. The operator manual switches and PLC control are conveniently located in the console. Components and wiring are neatly laid out and labeled for easy troubleshooting.
Controls - conveniently located in the front of the machine, to the right of out feeding material, the selector switches and pushbuttons allow the operator to manually control all machine functions including emergency stops.
The Mitsubishi PLC 100 or optional PLC 500 controller controls the Automatic cycle. The operator enters job information through the PLC interface keypad. The information required will be desired part length and quantity of pieces (with the optional PLC 500, the required angle at each end of the part are also entered). Up to 99 different jobs can be entered into the PLC memory, and can be called up and performed at any time. Also, a job queue function allows up to 5 jobs to be picked from the memory, and run consecutively.
In Manual mode - the PLC displays blade speed, feed rate and length system readout
(The optional PLC 500 also will display angle information). A single part operation can also be performed while in the Manual mode. The operator simply enters the desired part length, presses the cycle start button, starts the blade, and the machine will index that length, cut it off and raise the head back up. As well as the single part operation the optional PLC 500 has an angle go to function, which allows the operator to enter a desired angle and have the machine automatically move the head to that angle.
In Automatic mode - the PLC displays blade speed, feed rate, part length, quantity required, and number of pieces cut (and angle information with optional PLC 500)
Blade Drive - the blade drive motor is controlled by a Mitsubishi AC inverter drive. Provides smooth operation and infinite adjustment from 50 to 350 sfm.
Full Capacity Overhead Bundling - hydraulically powered overhead clamp that moves down on the material from above. Its downward (clamping) and upward (unclamping) movement are controlled and timed with the opening and closing of the moveable vise. Very effective, and necessary for bundle cutting various material shapes, widths & sizes. Can also be effective in dampening of cutting vibration.
Variable Vise Pressure - allows for adjustment of the clamping pressure of both vises. Recommended for thin wall tubing and other light material applications where standard vise pressure may deform the material.



Hyd-mech band saw m-16A hydmech automatic bandsaw amada